Відео

that is bit dangerous but works in hands of skilled person. I am quite sure who ever tries this for first time it will overheat bearings and they will not have long or happy life.

Why didnt you just pour water in them. Waters already paid for. Break clean costs

No shit, once it is torn down. Ugh

Can you make a video on a J series trans. I have a 05 Accord J30 6 speed. 😕 I have third gear grind when shifting into third.

Great video you got a new sub.

Good video can you use water if you don't have the brake cleaner

Duma!

Oven would be safer. 200°. If you hit 300 to 400° the steel is ruined, becomes brittle

Don't think grease in new bearing will be too happy with that heat.

Hmmm the bearing life is shorten then.

Question on those Honda transmissions, would you replace the needle bearing as well? Do they usually give bad or get really worn?

Wished you could upload a new video. The information seems very good but I had no idea what you were talking about with you showed what's good and smooth and what was bad like a saw. Thanks

Is that MAP gas or standard propane?

It'd be more helpful if you did this video while disassembling a removed one.

buy a fucking good camera

In your opinion, what causes just sticking gears? Got an M5OD R1 that started sticking going into first and second. Doesn't grind at all. Changed fluid and it was good for a week, then it started back. Usually working the stick for a couple seconds will ease it into gear, sometimes it takes a little longer though. Thinking of trying another fluid change, maybe there's some sludge still floating around in there. What are your thoughts?

props for making this video, its helpimg me learn 8 years later!

So what was the problem?

where's your shop located?

Muched needed thank u helped me save 500..subscribed! Can i install a Lsd in a non Lsd gsr engine as you would to upgrade a itr (s80) to a quife,kaaz,cusco, m factory etc?

Show how to get them off.

I use a growler for heating bearings.

makes a video about testing it outside of the car, has it in his car...

5:44 Going for a world record?

So? how long is that supposed to last???? this ain't downtown Kabul!

Will it shrink it enough to put the diff in.the freezer without using heat on the bearings?

Whats that wet shiny stuff at the low point of the first cylinder ?

O god vlsd thoes are junk

Good shit. But I skip the whole 3 degrees off on the crank tdc mark. Works great

Why not use a race driver set?

Great video, also just a tip clean the valves and measure them all a digital caliper won't lie. And mark where you measure

Hey man need help with my 94 Honda Accord 2.2l m/t I changed the clutch master and slave cylinder s but it still wound go into gear any thoughts

Wouldn't using rubbing alcohol be cheaper than brake clean? It's like $1 for a 1/2 liter. I like to see mechanics that really are giving good information and not spreading bs . I have seen guys on here I wouldn't trust to work on a old junk yard lawn mower. It's nice to see a honest mechanic

Damn! You made it look so easy! LMAO I did it on mine, I’m on my 4th attempt! Problem is, if the belt is tight, then the timing is whacked, but if it’s loose then the timing is fine 😫 great vid though!👍🏼👍🏼

Good job teng!

Hey i got a question, do u know if I can use the ls differential and put b16 ring gear onto it. Or is the b16 and ls differential different

u stop when u get to the good stuff!

Do you have any videos on splitting an h series? I followed this video on it but it won't split.

do not do this it is not the right way check it before you take the head off with air pressure

Why can't you just use water. It's cheaper than brake cleaner and kerosene.

On a 2000 civic ex d series, I order input shaft bearing 91002ps0013, they said I should replace another bearing 91004pl3b03, were does this bearing go? Thanks great video

98 gsr trans my fifth gear pops out immediately

You said bent valves cost a few hundred to fix. She shop gave me 1500 est to have machined to fix it.

Thanks for your effort and willingness to share your knowledge ;)

good job

Theng , good video, I have a honda accord with APG6 standart transmission the problem is that the cv axle driver side is wobbling bad and look like is part of the differential whats wobbling, the question is do I have to change the whole differential or can be replaced the bearings?

informative, thanks! long is fine as long as its got info.

We don't care how long your video is as long as they are very informative, so just do your thing explaining it to us, as we appreciate you sharing your knowledge on these transmissions... Your video helped me a lot, again, thank you!!!

Awesome vid bro! Subbed! Thanks!!! PS Do you happen to have a rebuilt B18 transmission for sale so I can slap it on my Inte now then I can play around with the current transmission?

hammering on a shaft entering a bearing will cause brinelling on the bearing races leading to premature bearing failure. maintenance 101.